Pool Resurfacing in Phoenix, AZ

Serving Scottsdale, Phoenix, Paradise Valley, Fountain Hills, and surrounding areas since 1971

Schedule On-Site Estimate
& Equipment Evaluation

The inside surface of your pool takes sun, chemicals, and Arizona's hard water every day. When it gets rough, stained, or starts to flake, resurfacing replaces it. Aqua Sentry Pools resurfaces pools in Phoenix, Scottsdale, Paradise Valley, Fountain Hills, and the surrounding areas. The first step is an on-site estimate, so you can see what your pool needs before you decide anything. Call (602) 713-6226 or request a visit online.

Signs your pool needs resurfacing in Phoenix

Pool surfaces wear slowly, so the signs are easy to put off. This table shows what each one can point to and what we check first. Several have other causes, so a technician should look before you commit.

Sign

What it can mean

What we check

A rough surface that scratches your feet or swimsuit

What it can mean

A worn finish, or etching from water that has been out of balance

What we check

The surface across the whole pool, and the water balance

Stains that brushing and chemistry do not clear

What it can mean

Scale or discoloration, or a finish past its life

What we check

Whether cleaning or an acid wash fits before resurfacing

Cracks, chips, flaking, or spots that sound hollow when tapped

What it can mean

A finish that has lost its bond, or cracks in the shell

What we check

How far it has spread, and whether the cracks are surface or structural

Loose or missing waterline tile

What it can mean

A failing tile bond at the waterline

What we check

The tile and the coping around it

Water level dropping faster than evaporation explains

What it can mean

A leak at a crack, a fitting, or an underground line

What we check

Leak detection through our pool and spa repair service, before any finish goes on

Water balance matters for any finish. NPT, a finish manufacturer, says water that is out of balance can etch the surface on one side and leave scale and discoloration on the other. Phoenix.gov says hardness in Arizona can reach 20 grains per gallon, so keeping the water balanced is part of protecting a new finish here.

Pool finish options: plaster, pebble, and quartz

We resurface with three types of finish. All three go on over a prepared pool shell and need the same careful start-up, and the finish maker's instructions control the details.

Plaster

The traditional cement-based finish, applied as a smooth surface.

Pebble

Small stone mixed into the cement, which gives the surface texture.

Quartz

Quartz mixed into the cement, which gives the surface color options.

We go over all three during your on-site estimate, so look at samples in the light your own pool gets.

What pool resurfacing involves

1

We look at the pool and go over finish options during the estimate.

2

The pool is drained.

3

The surface is prepared, and waterline tile and coping are repaired or replaced as needed.

4

The new finish is applied.

5

The pool is refilled in one run.

6

Start-up service begins, to bring the water chemistry into balance on the newly resurfaced pool.

NPT's start-up guide says filling can take between 18 and 36 hours and should not be stopped, because stopping can leave a visible line at the stopping point. Fill times depend on your pool and water supply.

Service Excellence… No Excuses

Client Testimonials

Hear from our satisfied customers who have experienced the Aqua Sentry difference

Where We Service Pools

Our store is now at 3246 E Cactus Rd in Phoenix, and our technicians still service pools across Scottsdale, Paradise Valley, and Fountain Hills, as well as North Phoenix and Carefree. The pin shows the store, and the shaded area shows where we work.

Phoenix–Scottsdale Service Area Map 2

Why the pool has to be drained

Resurfacing requires an empty pool, and where that water goes matters. This table covers the City of Phoenix guidelines.

Topic

What the City of Phoenix says

Where a whole pool goes

Down the home's sewer clean-out, or reuse the water on landscaping where you can

Flow rate

No more than 12 gallons per minute is recommended, and most pool filter pumps discharge too fast

Safer equipment

A small submersible pump, which drains the pool slowly

Where it must not go

The street, an alley, or a septic tank

Clean-outs in a wall

A higher risk of water backing up into the house

Homes with no sewer clean-out

A permit is required to send clean, de-chlorinated water to the right-of-way

Permit limits

No more than 50 gallons per minute and under 1 ppm chlorine, and saltwater pool water and filter backwash are not allowed

Refill timing

Refilling in the January, February, and March billing cycles costs much less than when water rates are higher

Sewer fee

A big jump in water use can change the sewer fee, which the city recalculates in July, and review requests made more than 60 days after the July bill date are not eligible

These are City of Phoenix rules. If your home is in Scottsdale, Paradise Valley, Fountain Hills, or another city, check with that city's water or stormwater office before draining.

tile and coping by aqua sentry pools

Waterline tile and coping during resurfacing

The waterline is where the finish, the tile, and the coping meet, so it gets looked at during every resurfacing. There are two parts to it:

Waterline tile

The band of tile at the waterline, where hard water leaves deposits. We repair or replace it when it is cracked or loose, and tile that is only dirty is a different job.

Coping

The cap along the edge of the pool, where the pool meets the deck. We repair or replace it when it needs it as part of the job.

If you want to change how the tile and coping look, or redo the whole edge, that falls under our pool remodeling work.

What to expect before, during, and after resurfacing

Before

You get an on-site estimate and a schedule for your pool. Timing depends on the pool and the finish, so we plan around yours.

During

The pool is drained, prepared, and finished. The table above covers where the drained water goes, which depends on your city.

After

The first 28 days matter most, because NPT's start-up guide says a new finish is especially susceptible to staining, scaling, and discoloration in that period. Start-up care for those 28 days:

  • Brush the pool surface at least twice a day to remove plaster dust.
  • Test the water daily at first, and keep it balanced.
  • Do not use wheeled cleaners, built-in cleaners, or robotic cleaners until the 28 days are up.
  • Do not add salt for 28 days.
  • Do not shock the pool for the first 30 days.
  • Run the filtration system continuously for at least the first 72 hours.
  • Do not turn on the pool heater until the plaster dust is gone, which NPT says is typically between day 4 and day 10.

Do not swim until the water is balanced. Our start-up service handles the water chemistry on a newly resurfaced pool. If you are on a weekly pool cleaning route, tell us when the pool will be refilled so the two schedules line up.

Pool Resurfacing or Pool Remodeling?

Resurfacing and remodeling overlap at the edges, so here is how they differ.

Resurfacing

Remodeling

What it covers

Resurfacing

The inside surface of the pool

Remodeling

Decking, lighting, water features, and equipment

Typical work

Resurfacing

Draining, surface preparation, a new finish, a refill, and start-up

Remodeling

Design and building work around the pool

Our estimate

Resurfacing

An on-site estimate

Remodeling

An on-site estimate through our pool remodeling work

Plenty of pools need only one of them, and the estimate is the place to sort out which.

When a repair makes more sense than resurfacing

Resurfacing is not always the answer. This table shows where we start for each situation.

What you see

Where we start

Tile that is dirty but sound

Where we start

Tile cleaning, which we offer

Stains in one area, or stains from a water-balance problem

Where we start

Correcting the cause first, and an acid wash may fit

A pool that is losing water

Where we start

Leak detection, before any finish goes on

A surface that is rough everywhere, with flaking or hollow spots spreading, or a finish worn through

Where we start

Resurfacing, since patches tend to be a short-term fix

We will tell you what we see.

Pool resurfacing questions

How much does pool resurfacing cost?

Cost depends on your pool's size, finish, and surface condition. An on-site estimate gives you a number for your pool, so you can compare it before you decide.

How soon can I swim after resurfacing?

NPT's start-up guide says not to swim until the water is properly balanced and sanitized, and that the first 28 days need careful care. Ask for the timeline for your pool's finish and size.

Can I use my robotic cleaner after resurfacing?

Not right away. NPT says to hold off on wheeled devices and automated or robotic cleaners until the 28-day start-up is finished, so the surface is brushed by hand until then.

Does a saltwater pool need anything different?

Yes. NPT says not to add salt for the first 28 days, and that waiting up to six weeks before running a salt-water generator can be better for the finish.

Will resurfacing fix a leak?

Not by itself. If your pool is losing water, the leak has to be found first, and we do leak detection and underground plumbing repair before any finish goes on.